Built for Upstate NY road salt and snowmelt
A 100% solids moisture vapor barrier epoxy base and clear polyaspartic topcoat seal the slab so winter slush, road salt, and brine wipe away.
Garage Floor Coatings
Turn bare, salt-damaged garage concrete into a bright, easy-to-clean floor built with a 100% solids moisture vapor barrier epoxy base and a clear polyaspartic topcoat.
Best for: Homeowners, 1- to 3-car garages, home workshops, residential pole barns
Garage concrete in the Hudson Valley and Capital District takes a beating from winter road salt, snowmelt, hot tires, and seasonal freeze-thaw swings. Left bare, the slab dusts, pits, and absorbs oil and brine. A professionally prepared coating system seals the concrete into a clean, finished room that sweeps and squeegees clean in minutes.
Every garage project starts with a free on-site estimate where we inspect the concrete, run a digital moisture meter test, and check surface temperature with a thermal gun in spring and fall to make sure the slab is above 40 degrees F. During prep, we mechanically diamond grind the floor and fill cracks with a fast-curing two-part epoxy filler that stays flexible with the slab, then grind the repairs flush.
For most homeowners, we install our flake epoxy system or our premium quartz epoxy upgrade: a 100% solids moisture vapor barrier (MVB) epoxy base coat (used on garages and basements because they carry more moisture, unless the slab is brand new with radiant heat or an under-slab plastic vapor barrier), a broadcast layer of vinyl flake or colored quartz, and a clear polyaspartic topcoat that will not yellow in sunlight and moves flexibly with the concrete. We also install solid-color garage floors built with two to three coats of 100% solids epoxy and a urethane topcoat with optional traction aggregate. Residential garage installations include our residential warranty: Lifetime delamination and workmanship warranty, transferable to new owners. Excludes cracking and slab movement.
Benefits
A 100% solids moisture vapor barrier epoxy base and clear polyaspartic topcoat seal the slab so winter slush, road salt, and brine wipe away.
Every flake and quartz garage floor finishes with a clear polyaspartic topcoat that stays flexible with the slab and will not yellow near open garage doors.
We mechanically diamond grind the concrete and fill cracks with a fast-curing two-part flexible epoxy filler ground flush before coating.
Every estimate includes a digital moisture meter test, plus a thermal temperature gun check in spring and fall to verify the slab is above 40 degrees F.
Choose decorative flake, premium colored quartz, or solid-color epoxy, with optional aluminum oxide or traction aggregate for extra grip.
Lifetime delamination and workmanship warranty, transferable to new owners. Excludes cracking and slab movement.
Common Problems Solved
Bare concrete dusts and tracks grit into the house
A multi-layer coating seals the surface completely so fine concrete dust stops forming.
Oil drips, rust, and winter salt brine leave permanent stains
The non-porous clear polyaspartic topcoat keeps automotive fluids and road salt on the surface for quick cleanup.
Cracks, spalling, and sub-slab moisture ruin DIY floor kits
We diamond grind the slab, repair cracks flush with two-part flexible epoxy, and apply a 100% solids MVB epoxy base coat.
Sunlight turns clear epoxy yellow near the garage door
Our clear polyaspartic topcoat resists UV ambering where sunlight hits the garage apron and threshold.
Our Process
We inspect the concrete, prepare the surface, repair eligible defects, install the selected system, and finish with a final walkthrough.
We measure your garage, test moisture with a digital meter, and check slab temperature in spring and fall to confirm the concrete is above 40 degrees F.
We diamond grind the entire garage floor to remove surface contamination and open a clean mechanical profile for the base coat.
Cracks and pitting are filled with a fast-curing two-part epoxy filler that sets hard in minutes and stays flexible, then diamond ground flush.
We apply a 100% solids moisture vapor barrier epoxy base coat (unless coating a brand-new slab with radiant heat or an under-slab plastic vapor barrier) and broadcast decorative flake or quartz.
We seal flake and quartz floors with a clear polyaspartic topcoat (with optional aluminum oxide for extra grip) and review your 24, 48, and 72 hour cure schedule.
Finish Options
100% solids MVB epoxy base, vinyl flake broadcast, and a clear polyaspartic topcoat that hides dirt and adds natural grip.
100% solids MVB epoxy base, colored quartz aggregate broadcast, and a clear polyaspartic topcoat for maximum abrasion and wet-area traction.
Two to three coats of 100% solids epoxy finished with a protective urethane topcoat, with optional mixed-in aggregate for traction.
Maintenance
A coated garage floor stays clean all year with a few basic habits.
FAQs
Flake and quartz garage floor installations take 2 to 3 days minimum on site, while solid-color and metallic systems take 4 to 5 days minimum (moisture mitigation or extensive slab repairs can extend those timelines). After the final topcoat on a standard garage, wait 24 hours for light foot traffic (socks or clean shoes), 48 hours before moving light items like cabinets and toolboxes back in, and 72 hours before parking a car or truck. A faster-drying one-day option is possible in certain situations.
Peeling happens when a coating is rolled over poorly prepped or damp concrete, or when a low-grade topcoat softens under hot tires. We diamond grind every slab, test moisture at the estimate, apply a 100% solids moisture vapor barrier epoxy base coat on garage slabs, and finish flake and quartz floors with a clear polyaspartic topcoat with hot-tire rated options available.
Yes. We fill cracks and surface defects with a fast-curing two-part epoxy crack filler that cures hard in minutes and stays flexible with the concrete, then diamond grind the repair flush before applying the base coat.
Broadcast flake and quartz systems have natural surface texture that provides grip underfoot. For steeper aprons, entry lanes, or extra winter traction, we can add aluminum oxide to the clear polyaspartic topcoat, or mix traction aggregate into the urethane topcoat on solid-color floors.
Gallery Examples
An example of a finished floor by Next Level Epoxy Inc.
Schedule a free on-site estimate, with your quote the same day. Send a few details and photos and we will help you choose the right coating system.
Get a Free Quote